Jump to content

DIY cooling fans...


jacet

Recommended Posts

Hi all,

Started a project 5 weeks ago and took me all this time to get all the bit and pieces to build a cooling fan unit for my 250 litre tank... Yep big tank but that is my main display tank and could not keep crystals in there as really struggled to keep it under 26-27 in summer with adding ice blocks and so on... So today on a raining sunday afternoon in brisbane I did my water change cheched the temp and it was 25 as we have had cool weather for the last week so happy with that...

So I made this thing from fans from jaycar and a bit of plastic I machined and bent at work (love the CNC computer router). So it has cost me as much as a normal cooling fan I think but I made it and I can add to it easy enough..

Thing I used is

3 80mm CPU fans, dust and moisture proof

1 piece of white acrylic 4.5mm thick computer cut

2 metres of figure 8

316 stainless steel 5/32 x38mm bolts and nuts to suit

solder and electrial tape

zip ties

60 mins of my time all up...

I will post pics when i up load them to the computer

Happy to answer any question just give me some time to post some pics and i will answer them soon...

Link to comment
Share on other sites

post-1938-139909849624_thumb.jpgpost-1938-139909849618_thumb.jpgpost-1108-139909859908_thumb.jpgpost-1938-139909849621_thumb.jpg

They are set on a timer to come on and of with the LED lights so it has a chance to cool a bit before the T5HO come on and cool after they go of.. It has been 20 mins with them on and have already dropped the tank 1 deg already... Not bad for 3 little fans...

As you can see from the pics they are on a 45deg angle facing the surface of the water. They suck the air in from the back of to hood where the holes are for all the filters and leads come into the tank and as a bonus the LED lights really have the ripple affect with the air blowing across the water... I will dig out the specs on the fans over the afternoon...

post-599-139909848594_thumb.jpg

post-599-139909848596_thumb.jpg

post-599-139909848598_thumb.jpg

post-599-139909848599_thumb.jpg

Link to comment
Share on other sites

[TABLE=width: 100%]

[/TD]

[TD=class: type]

80mm Super Long-Life Low-Noise MagLev Bearing Case Fan

Featuring a patented Nanoflux bearing that incorporates magnetic levitation technology and precise manufacturing, these premium quality fans ensure an extremely long operational life of 100,000hrs at 40ºC (even longer at 25ºC). The unique self-lubricating maglev bearing design offers extremely long life, extremely low noise levels compared to traditional ball bearings, and also offers the ability for the UV light reactive fan impeller to be removed for cleaning. Dust and water proof to IP54 , these fans are sure to last even in harsh conditions.

[TABLE=class: type]

[TD=bgcolor: #E2E3E3, colspan: 2]Specifications

[TD=width: 193]Voltage (V)[/TD]

[TD=width: 78]12VDC[/TD]

Starting voltage

5VDC

Current (mA)

100

Dimensions (mm)

80 x 80 x 25

Air volume (m3/min)

0.8

Air volume (CFM)

28.1

Speed (RPM)

2000

Noise (dBA)

21

Bearings

Nanoflux magnetic levitation

Housing

Polycarbonate

Impellers

UV reactive polycarbonate

Connections

Flylead with 3 pin molex

[/TABLE]

[/TD]

[/TABLE]

Link to comment
Share on other sites

Do you mind showing us how you wired them up? Is each fan running off it's own transformer?

Link to comment
Share on other sites

Looks great jacet! Could have easily bought one but as you said you made it and it feels great when it works and something to be proud of. Just isn't the same feeling when you buy it.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • sdlTBfanUK
      Thats a great photo, beautiful blue bolt, I hope it survived the molt without dropping the eggs! I think I can just about see some black dots (eyes) on the central egg but can't be 100% sure. I used to (and plan to again) do weekly water change of 10-15% but if you do too large or quick (not drip in new water) that would likely trigger a molt. What KH are they in, my new setup is sitting at (and refusing to budge) KH 3 and PH 7.5 so I may have to settle for neocaridina shrimp this time as opposed to the caridina I want, though not looking/deciding just yet, give the tank a bit more of a run in! Tap water here starts at kH 14, tds 320, when filtered goes to KH 0 and PH 6 but when put in the tank keeps going to KH3 and PH 7.5 despite 3 x 50% water changes???? You may be at 'maximum capacity' with only 20L tank especially if the tank is a cube type rather than shallow type?
    • beanbag
      Right now this tank only has blue bolts and golden bee (red bolts?).  The eggs start off all brown, but at the end, I notice that some are kind of a clear pink-ish color.  So I don't know if that is the egg color of dud or golden bee.  Picture of shrimp only about half hour before molting. The water is always RO + remineralizer, so it should be ok. The tank seems to still be on a "good streak" ever since I started the regimen of weekly water change, monthly gravel vac and plant trim.  The point being to keep the amount of waste low and removing moss / floating plants so that the nitrates go towards growing algae.  At one point, I had three berried females, but only netted about half dozen babies by the end, due to this early molting problem.  There might be about 30-40 shrimp total in 5 gallons, but still very few full-sized adults.
    • ngoomie
      Alright, I've done a bit more research on gentian violet's cancer-causing potential but I haven't yet done research on malachite green's to compare. But from reading the California propositon 65 document about GV (North Americans incl. some Canadians will recognize this as the law that causes some products they buy to be labelled with "known to the state of California to cause cancer", including the exact product I bought) it seems that the risk of cancer is related to internal use, either injection or ingestion. Speaking of ingestion, I think GV bans mainly relate to its use in treating fish/shrimp/etc. which are intended for human consumption, because of the above. And in countries where GV isn't banned for this purpose, it does seem to get used on various species of shrimp without causing any issue for the shrimp themselves (at least enough so for shrimp farming purposes). See the following: In February, the FDA Began Rejecting Imported Shrimp for Gentian Violet and Chloramphenicol (2022 article by Southern Shrimp Alliance) FDA Starts New Calendar Year by Refusing Antibiotic-Contaminated Shrimp from Three BAP-Certified Indian Processors and Adding a BAP-Certified Vietnamese Processor to Import Alert (2024 article by Southern Shrimp Alliance) Southern Shrimp Alliance and some other organizations have tons of other articles in this vein, but I'd be here for a while and would end up writing an absolutely massive post if I were to link every instance I found of articles mentioning shrimp shipments with gentian violet and/or leucogentian violet registering as contaminants. That being said, I know shrimp farmed for consumption and dwarf shrimp are often somewhat distantly related (in fact, the one time a shrimp's species name is listed that I can see, it's the prawn sp. Macrobrachium rosenbergii, who at best occupies the same infraorder as Neocaridina davidi but nothing nearer), but this at least gives a slightly better way of guessing whether it will be safe for aquarium dwarf shrimp or not than my bladder snail anecdote from the OP.
    • sdlTBfanUK
      I would hazard a guess that perhaps those eggs were unfertilized and thereby unviable? Did the eggs change colour, usually yellow to grey as the yolks used up, or any eyes in the eggs. Is your water ok, using RO remineralised and the parameters in range, as I have heard others say that if the water isn't good it can 'force' a molt? How is it going overall, do you have a good size colony in the tank, you may have reached 'maximum occupancy' as a tank can only support so many occupants.
    • beanbag
      Hello folks,  The current problem I am having is that my Taiwan bee shrimp are molting before all their eggs have hatched.  Often the shrimp keep the eggs for 40+ days.  During that time, they lose about half or so, either due to dropping or duds or whatever.  Shortly before molting they look to have about a dozen left, and then they molt with about half a dozen eggs still on the shell.  Then the other shirmp will come and eat the shell.  These last few times, I have been getting around 0-3 surviving babies per batch.  I figure I can make the eggs hatch faster by raising the water temperature more (currently around 68F, which is already a few degrees higher than I used to keep it) or make the shrimp grow slower by feeding them less (protein).  Currently I feed Shrimp King complete every other day, and also a small dab of Shrimp Fit alternating days.  Maybe I can start alternating with more vegetable food like mulberry?  or just decrease the amount of food?
×
×
  • Create New...