Jump to content

New AWESOME TDS/EC/SALINITY PEN


Eshrimp

Recommended Posts

Ok so after being burnt by my old Chinese TDS pen, i started my usual anal retentive search for a GOOD decent price HIGH quality pen for my testing (my wife says i sometimes research stuff way too much LOL)

and after hours and hours calls and call to lab equipment reps, water quality plant manufacturers and SA water technicians this is the result.

This little puppy has a lab grade probe, the most accurate conversion matrix sys in the commercial market and most importantly IT LOOKS BLOODY COOL. (It looks and feels very similar to a Dr Who sonic screwdriver :D)

i have been using it for a about a week now and its incredible. You can choose from EC, two different TDS. Conversion standard or two difrent salinity standards. Its probe tip can be calibrated and replaced as well.

IMO for the 200.00 price tag it is a bullet proof long lasting accurate pice of kit that now i can trust.

Have a look...

CCC078F8-9853-4D35-A259-20FEF7CDED63.jpg

Link to comment
Share on other sites

my $10 ebay pen works great!!!

I know because I test my RO unit water all the time and when i change the DI resin the tds goes back to 0 :)

Link to comment
Share on other sites

my $10 ebay pen works great!!!

I know because I test my RO unit water all the time and when i change the DI resin the tds goes back to 0 :)

It isn't that hard for it to be zero. It may still be incorrect though, unless you check it against a known tds solution which isn't zero there is no way of knowing.

Link to comment
Share on other sites

Awesome review dude, would love to know the best place to get one too, thanks heaps! :victorious:

Link to comment
Share on other sites

Neosin my Chinese pen use to and still reads 0 on my RO bin and 200 TDS in my display tank, after I installed a G3 filter I discovered my tank was ACTUALLY at about 350+ TDS (600EC on G3).

I hope it's ok and since you guys ask here is the AU distributors page... Group buy maybe? I'm sure I could have them cut us a deal maybe?

http://www.aquacorp.com.au/myronl_digital_PT2.html

Link to comment
Share on other sites

These look awesome! Good find Eshrimp and thanks for sharing. I think their sales on these pens may be about to rise.........

Link to comment
Share on other sites

Yeah this company makes some very very cool testing equipment. There is even a hand held PH/TEMP/ORP/GH/KH/TDS/EC all in one meter. It even sends results wirelessly to a designated PC if you want...(can you guys tell I'm a gadget geek?)

have a look... I would have gone for this one if it could also be used for my marine stuff but no good for saltwater :/

http://www.aquacorp.com.au/myronl_digital_9PIII.html

Link to comment
Share on other sites

I would be definately interested on a group buy for the TDS pen not sure about the PH meter though.... yet. How do we set one up?

Neosin my Chinese pen use to and still reads 0 on my RO bin and 200 TDS in my display tank, after I installed a G3 filter I discovered my tank was ACTUALLY at about 350+ TDS (600EC on G3). I hope it's ok and since you guys ask here is the AU distributors page... Group buy maybe? I'm sure I could have them cut us a deal maybe?http://www.aquacorp.com.au/myronl_digital_PT2.html
Link to comment
Share on other sites

  • 2 weeks later...

Since it seams their is a bit of interest in these little beauties im going to post pictures of the instructions so you guys can make your own judgment. Again IMO after using for a couple of weeks now this thing ROCKS!

it comes with this nifty little removable cup to use when calibrating so you only use a bit of the calibration fluid.

39AE199C-95ED-482F-9E54-CB7F872A8669.jpg

FF902D17-79B6-4D9D-AA1B-52F672DE3829.jpg

D09D270A-A36D-46A1-8725-C769813211FB.jpg

Notice the red led that lets you know when the testing is actually happening and when it is done testing :D

58591519-2489-4F50-B419-68E54818D88F.jpg

Link to comment
Share on other sites

I have to admit these look pretty awesome, so far though my bluelabs truncheon seems to be holding up well (shows EC, TDS and ECx700) but I cant calibrate it as far as I know

-edit-

my bluelab truncheon only starts at EC 0.2, TDS 100. Looking this up does it actually start reading from TDS 1? trying to figure out just how much lower your pen can go

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • sdlTBfanUK
      Thats a great photo, beautiful blue bolt, I hope it survived the molt without dropping the eggs! I think I can just about see some black dots (eyes) on the central egg but can't be 100% sure. I used to (and plan to again) do weekly water change of 10-15% but if you do too large or quick (not drip in new water) that would likely trigger a molt. What KH are they in, my new setup is sitting at (and refusing to budge) KH 3 and PH 7.5 so I may have to settle for neocaridina shrimp this time as opposed to the caridina I want, though not looking/deciding just yet, give the tank a bit more of a run in! Tap water here starts at kH 14, tds 320, when filtered goes to KH 0 and PH 6 but when put in the tank keeps going to KH3 and PH 7.5 despite 3 x 50% water changes???? You may be at 'maximum capacity' with only 20L tank especially if the tank is a cube type rather than shallow type?
    • beanbag
      Right now this tank only has blue bolts and golden bee (red bolts?).  The eggs start off all brown, but at the end, I notice that some are kind of a clear pink-ish color.  So I don't know if that is the egg color of dud or golden bee.  Picture of shrimp only about half hour before molting. The water is always RO + remineralizer, so it should be ok. The tank seems to still be on a "good streak" ever since I started the regimen of weekly water change, monthly gravel vac and plant trim.  The point being to keep the amount of waste low and removing moss / floating plants so that the nitrates go towards growing algae.  At one point, I had three berried females, but only netted about half dozen babies by the end, due to this early molting problem.  There might be about 30-40 shrimp total in 5 gallons, but still very few full-sized adults.
    • ngoomie
      Alright, I've done a bit more research on gentian violet's cancer-causing potential but I haven't yet done research on malachite green's to compare. But from reading the California propositon 65 document about GV (North Americans incl. some Canadians will recognize this as the law that causes some products they buy to be labelled with "known to the state of California to cause cancer", including the exact product I bought) it seems that the risk of cancer is related to internal use, either injection or ingestion. Speaking of ingestion, I think GV bans mainly relate to its use in treating fish/shrimp/etc. which are intended for human consumption, because of the above. And in countries where GV isn't banned for this purpose, it does seem to get used on various species of shrimp without causing any issue for the shrimp themselves (at least enough so for shrimp farming purposes). See the following: In February, the FDA Began Rejecting Imported Shrimp for Gentian Violet and Chloramphenicol (2022 article by Southern Shrimp Alliance) FDA Starts New Calendar Year by Refusing Antibiotic-Contaminated Shrimp from Three BAP-Certified Indian Processors and Adding a BAP-Certified Vietnamese Processor to Import Alert (2024 article by Southern Shrimp Alliance) Southern Shrimp Alliance and some other organizations have tons of other articles in this vein, but I'd be here for a while and would end up writing an absolutely massive post if I were to link every instance I found of articles mentioning shrimp shipments with gentian violet and/or leucogentian violet registering as contaminants. That being said, I know shrimp farmed for consumption and dwarf shrimp are often somewhat distantly related (in fact, the one time a shrimp's species name is listed that I can see, it's the prawn sp. Macrobrachium rosenbergii, who at best occupies the same infraorder as Neocaridina davidi but nothing nearer), but this at least gives a slightly better way of guessing whether it will be safe for aquarium dwarf shrimp or not than my bladder snail anecdote from the OP.
    • sdlTBfanUK
      I would hazard a guess that perhaps those eggs were unfertilized and thereby unviable? Did the eggs change colour, usually yellow to grey as the yolks used up, or any eyes in the eggs. Is your water ok, using RO remineralised and the parameters in range, as I have heard others say that if the water isn't good it can 'force' a molt? How is it going overall, do you have a good size colony in the tank, you may have reached 'maximum occupancy' as a tank can only support so many occupants.
    • beanbag
      Hello folks,  The current problem I am having is that my Taiwan bee shrimp are molting before all their eggs have hatched.  Often the shrimp keep the eggs for 40+ days.  During that time, they lose about half or so, either due to dropping or duds or whatever.  Shortly before molting they look to have about a dozen left, and then they molt with about half a dozen eggs still on the shell.  Then the other shirmp will come and eat the shell.  These last few times, I have been getting around 0-3 surviving babies per batch.  I figure I can make the eggs hatch faster by raising the water temperature more (currently around 68F, which is already a few degrees higher than I used to keep it) or make the shrimp grow slower by feeding them less (protein).  Currently I feed Shrimp King complete every other day, and also a small dab of Shrimp Fit alternating days.  Maybe I can start alternating with more vegetable food like mulberry?  or just decrease the amount of food?
×
×
  • Create New...