Jump to content

Eheim + Lilly pipe Velocity problem


amkr

Recommended Posts

Hi,

I previously had an Aquis 500 on my 2ft tank, recently I got myself an enormous Eheim Pro 3E 350 (16mm hoses).

but I had 13mm lilly pipes. So I stepped these down to 13mm using an adaptor to get them to fit on.

The problem I have though, is that even on the lowest pump setting, I've got a bit of a strong water current.

so I've been trying to work out how to best remedy my water velocity problems.

This is the outflow I have currently (13mm)

post-3445-139909851821_thumb.jpg

Im wondering if a straight swap to the 17mm lilly pipes will reduce the velocity? I've also noticed that CAL have an outflow with a larger bell mouth, I'm not sure if that would reduce the velocity aswell.

Anyone have any ideas or suggestions?

post-3072-139909860625_thumb.jpg

Link to comment
Share on other sites

Yeah a larger pipe will definitely reduce the velocity, reducing the size of the hose going to the one you're using now is causing the problem, just like putting your finger over the end of a garden hose causes higher pressure & more spray, same thing is happening in your tank :victorious:

Link to comment
Share on other sites

Thoertically, there's a few solution, depending on the decrease in flow %...

1. An inline tap to restrict the flow. Depending on the severity, this may cause stress on the pump, but conservatively, if you're decreasing it only by 5-10%, it shouldn't cause any issues.

2. If you use say a 13mm pipe, this will cause more water friction running through the pipe (in comparison to a 16mm), thus decreasing the water volume, but not neccesarily the velocity. So using a 13mm pipe onto a large mouth lilly pipe may solve the issue....again it's dependable upon how much you're trying to reduce it by..

3. lengthening the hose, thus causing more water friction....

4. Ditch the lily pipe, and go for a spray bar.

Hope this helps.

Link to comment
Share on other sites

Its one of those fangled eheim electronics, so impeding it with a tap isn't ideal, the filter has a feature where it increases speed to counter reduced flow from filter media.

I *think* the reduction in hose size is causing the increased velocity.. it sort of makes sense to me. I just want to be certain before I fork out for larger pipes.

I could lengthen the pipes I guess, they would stick out the side of the tank abit though.

No spraybars, Lilly pipes look nicer :)

Link to comment
Share on other sites

The larger outlet is the better choice, you'll have a reasonable flow but not excessive as compared with the 13mm ones. Do bear in mind the

circumference on a 13mm outlet is 40.84mm whereas 16mm is 50.24 an increase of 20 - 25% roughly as you're trying to squeeze more

flow through the same tubing so the speed will increase. These numbers aren't strictly accurate as I'm not sure whether that is the inside or

outside diameter but either way increased speed and pressure due to flow restriction. It will add in a decreased life of your filter. Whereas

going to 17mm the pressure will stay the same as the 16mm as the pump won't be restricted.

Link to comment
Share on other sites

At the moment I've got a bit of 16mm eheim hose stuck infront of the outflow to break up the speed a bit which seems to work.

I'm hoping a 17mm outlet will cut the speed down to somewhere around the same velocity. I just don't want to spend the cash to find out it doesn't work.

Otherwise the only option I can think of is that wierd ass circular thing from ADA =/

Link to comment
Share on other sites

The larger outlet is the better choice' date=' you'll have a reasonable flow but not excessive as compared with the 13mm ones. Do bear in mind the

circumference on a 13mm outlet is 40.84mm whereas 16mm is 50.24 an increase of 20 - 25% roughly as you're trying to squeeze more

flow through the same tubing so the speed will increase. These numbers aren't strictly accurate as I'm not sure whether that is the inside or

outside diameter but either way increased speed and pressure due to flow restriction. It will add in a decreased life of your filter. Whereas

going to 17mm the pressure will stay the same as the 16mm as the pump won't be restricted.[/quote']

wouldnt it be better off going off the cross sectional area of the pipe. 132 mm^2 for 13 and 200mm^2 for 16mm...

So there is quite a significant difference in the area and therefore velocity.

the good old equation Q=(rho)*A*v.

so as the area decreases, for the same mass flow rate (q) the velocity is inversely proportional.

I would say that increasing your pipe to 16mm would approximately bring the velocity of the flow down by 1/3

Link to comment
Share on other sites

wouldnt it be better off going off the cross sectional area of the pipe. 132 mm^2 for 13 and 200mm^2 for 16mm...

So there is quite a significant difference in the area and therefore velocity.

the good old equation Q=(rho)*A*v.

so as the area decreases' date=' for the same mass flow rate (q) the velocity is inversely proportional.

I would say that increasing your pipe to 16mm would approximately bring the velocity of the flow down by 1/3[/quote']

This is why I wish I did physics =/

1/3 sounds like good numbers, i'm just hoping its enough.

Link to comment
Share on other sites

You could use a larger lily pipe, or a 3 way T and run two lily pipes.

All of the above ideas are correct by the way, they will all work. As will lengthening the hose to increase friction, using a narrower hose and adapters to add frictional pressure from expansion and contraction fitting losses as well as the friction from the increased water flow velocity.

I know you love maths Mark, so Q=U*A, Re=rho*U*d/mu for fully developed laminar flow, f=16/re and deltaPfriction=(4*f*l/d)*rho*U^2/2 and then use delta p friction = rho* delta U^2/2 to work out how much the water will slow down based on the added friction.

But the best way you can reduce the flow is to face the outlet towards the backglass, it'll disperse off there and circulate evenly around the tank still.

Link to comment
Share on other sites

This is why I wish I did physics =/

1/3 sounds like good numbers' date=' i'm just hoping its enough.[/quote']

the only issue is... i have been at the pub for a few hours so my maths may be a bit dodgy

Link to comment
Share on other sites

Yeah those laminar flow calcs aren't happening. I'm just going to stare at the formula wistfully and pretend im doing it in my head...

I really like that T adaptor idea! I didnt think of that at all.

I'll grab a set of 17mm pipes tomorrow and some extra hose (and a T piece if they have one). I think I'll position the pipes at the BACK of the tank facing forwards, it has less distance to travel before it hits a wall then. Will need to have a play and see what works best.

Whats the best configuration to run the 2 pipes in? 2 on one side and the inlet on the other?

Link to comment
Share on other sites

Settle down you lot.

I'm going to have to get a mod in here soon to delete all the maths posts so I don't look like so much of an idiot :dejection:

Link to comment
Share on other sites

Grabbed the 17mm pipe tonight, haven't fitted it yet though.

been busy watching Django!

Link to comment
Share on other sites

Grabbed the 17mm pipe tonight' date=' haven't fitted it yet though.

been busy watching Django![/quote']

Such a good movie!

Link to comment
Share on other sites

hell yeah, I lost it when he got to pick his own clothes... comes out in the bluest pimp suit possible.

Then at the plantation the girls like "It's bad he makes you wear that" - "I'm free remember" - "wait... you choose to dress like that!"

Link to comment
Share on other sites

LOL yeah!

Some of it's pretty shocking. I got really pissed off at what happens with the German dude at the end though...

Link to comment
Share on other sites

Good movie! All the Tarantino films are top quality.

Link to comment
Share on other sites

LOL yeah!

Some of it's pretty shocking. I got really pissed off at what happens with the German dude at the end though...

Im guessing you are German Torface ???

Link to comment
Share on other sites

I'm half German, but that's not why I was pissed off... I dont want to spoil it for anyone who might not have seen the film, but I was disappointed with his behaviour lol

Link to comment
Share on other sites

I was sort of hoping the German had some scheme up his sleeve. His death seemed a little out of character.

I added the 17mm pipe, its bloody huge but its cut the velocity down alot. I'd like to cut another 15% off it still though.

Im thinking of re-arranging the under cabinet goodies to cut it down a bit more.

Currently I have

FILTER --->(17mm)HEATER(17mm)--->(17mm)(13mm)REACTOR(13mm)(17mm)---->(17mm)Lilly Pipe

Im thinking maybe the 13mm reactor being the last exit may be increasing it a tad, so thinking changing to

FILTER --->(17mm)(13mm)REACTOR(13mm)(17mm)---->(17mm)HEATER(17mm)--->(17mm)Lilly Pipe

Which gives it a longer period of time in a larger diameter hose.

But my physics sucks something savage so this may not make a difference... whats everyone think?

Link to comment
Share on other sites

Smaller diameter hoses increases the friction, increases the velocity and add's what is known as fitting losses to the water through rapid contraction and expansion. If i was you i'd keep as much 13mm hose as possible.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • sdlTBfanUK
      Thats a great photo, beautiful blue bolt, I hope it survived the molt without dropping the eggs! I think I can just about see some black dots (eyes) on the central egg but can't be 100% sure. I used to (and plan to again) do weekly water change of 10-15% but if you do too large or quick (not drip in new water) that would likely trigger a molt. What KH are they in, my new setup is sitting at (and refusing to budge) KH 3 and PH 7.5 so I may have to settle for neocaridina shrimp this time as opposed to the caridina I want, though not looking/deciding just yet, give the tank a bit more of a run in! Tap water here starts at kH 14, tds 320, when filtered goes to KH 0 and PH 6 but when put in the tank keeps going to KH3 and PH 7.5 despite 3 x 50% water changes???? You may be at 'maximum capacity' with only 20L tank especially if the tank is a cube type rather than shallow type?
    • beanbag
      Right now this tank only has blue bolts and golden bee (red bolts?).  The eggs start off all brown, but at the end, I notice that some are kind of a clear pink-ish color.  So I don't know if that is the egg color of dud or golden bee.  Picture of shrimp only about half hour before molting. The water is always RO + remineralizer, so it should be ok. The tank seems to still be on a "good streak" ever since I started the regimen of weekly water change, monthly gravel vac and plant trim.  The point being to keep the amount of waste low and removing moss / floating plants so that the nitrates go towards growing algae.  At one point, I had three berried females, but only netted about half dozen babies by the end, due to this early molting problem.  There might be about 30-40 shrimp total in 5 gallons, but still very few full-sized adults.
    • ngoomie
      Alright, I've done a bit more research on gentian violet's cancer-causing potential but I haven't yet done research on malachite green's to compare. But from reading the California propositon 65 document about GV (North Americans incl. some Canadians will recognize this as the law that causes some products they buy to be labelled with "known to the state of California to cause cancer", including the exact product I bought) it seems that the risk of cancer is related to internal use, either injection or ingestion. Speaking of ingestion, I think GV bans mainly relate to its use in treating fish/shrimp/etc. which are intended for human consumption, because of the above. And in countries where GV isn't banned for this purpose, it does seem to get used on various species of shrimp without causing any issue for the shrimp themselves (at least enough so for shrimp farming purposes). See the following: In February, the FDA Began Rejecting Imported Shrimp for Gentian Violet and Chloramphenicol (2022 article by Southern Shrimp Alliance) FDA Starts New Calendar Year by Refusing Antibiotic-Contaminated Shrimp from Three BAP-Certified Indian Processors and Adding a BAP-Certified Vietnamese Processor to Import Alert (2024 article by Southern Shrimp Alliance) Southern Shrimp Alliance and some other organizations have tons of other articles in this vein, but I'd be here for a while and would end up writing an absolutely massive post if I were to link every instance I found of articles mentioning shrimp shipments with gentian violet and/or leucogentian violet registering as contaminants. That being said, I know shrimp farmed for consumption and dwarf shrimp are often somewhat distantly related (in fact, the one time a shrimp's species name is listed that I can see, it's the prawn sp. Macrobrachium rosenbergii, who at best occupies the same infraorder as Neocaridina davidi but nothing nearer), but this at least gives a slightly better way of guessing whether it will be safe for aquarium dwarf shrimp or not than my bladder snail anecdote from the OP.
    • sdlTBfanUK
      I would hazard a guess that perhaps those eggs were unfertilized and thereby unviable? Did the eggs change colour, usually yellow to grey as the yolks used up, or any eyes in the eggs. Is your water ok, using RO remineralised and the parameters in range, as I have heard others say that if the water isn't good it can 'force' a molt? How is it going overall, do you have a good size colony in the tank, you may have reached 'maximum occupancy' as a tank can only support so many occupants.
    • beanbag
      Hello folks,  The current problem I am having is that my Taiwan bee shrimp are molting before all their eggs have hatched.  Often the shrimp keep the eggs for 40+ days.  During that time, they lose about half or so, either due to dropping or duds or whatever.  Shortly before molting they look to have about a dozen left, and then they molt with about half a dozen eggs still on the shell.  Then the other shirmp will come and eat the shell.  These last few times, I have been getting around 0-3 surviving babies per batch.  I figure I can make the eggs hatch faster by raising the water temperature more (currently around 68F, which is already a few degrees higher than I used to keep it) or make the shrimp grow slower by feeding them less (protein).  Currently I feed Shrimp King complete every other day, and also a small dab of Shrimp Fit alternating days.  Maybe I can start alternating with more vegetable food like mulberry?  or just decrease the amount of food?
×
×
  • Create New...