Jump to content

External sensor for Hailea Chiller questions?


Heavyd

Recommended Posts

I am running a Hailea HC300 chiller on one of my tanks and am finding that the flow I am getting through it is insufficient (running an Eheim 2217). The chiller is measuring the temperature in the reservoir and thinks the water is cooler than it is, so it keeps switching on and off. I have been researching connecting an external temperature sensor, so that the chiller is responding to the the actual tank temperature rather than the temperature in the reservoir. The other alternative is to plug the chiller into a temperature controller that will manually turn off the power to the chiller when the tank reaches the desired temperature. I have already tried connecting an inline water pump to the system and have had poor results.

I would prefer to only have to connect an external sensor by unwiring the internal sensor and rewiring the external one. Otherwise I'm looking at getting an STC1000 temperature controller (link below). My only concern is about switching the chiller power off whilst it is running:

http://www.ebay.com.au/itm/All-purpose-Temperature-Controller-STC-1000-Whit-sensor-/320628773067

Has anyone performed either of these modifications? Can anyone suggest what external temperature sensor would work with the Hailea chiller?

Link to comment
Share on other sites

Got one of these on my rack system.

Paid $18 form Hong Kong (2 weeks delivery).

Easy to use and easy to hook up.

Well worth it.

I set the chiller to about 2 degrees lower than the setting you want to run the tank at.

The controller is set up at 26.5 degrees with .5 degrees +or-.

In other words the chiller gets powered on at 27 degrees and off at 26.5 degrees.

My heater is set at 26 degrees.

If it gets cool then the heater will be switched on at 26 degrees and off at 26.5 degrees.

It doesn't bother the chiller at all, the same thing happens when the chiller's built in thermostat switches it off.

post-696-139909847367_thumb.jpg

post-696-13990984737_thumb.jpg

post-696-139909847373_thumb.jpg

Link to comment
Share on other sites

Excellent. Thanks for the feedback and tips. I went and ordered the units already. I may have some more questions for you when I get it and it comes time to install it.

Link to comment
Share on other sites

Well, I received the STC1000 yesterday and wired it up today. So far seems like a great little unit and has been working well. The temperature the probe was showing was off by +0.9oC, so I recalibrated it against my Sera thermometer. I set the temperature to cool to 24oC and to kick in at 24.7oC. Has been working ok for 2 to 3 cool cycles so far. Without this controller the chiller would only cool down to 24.8oC before switching off. Will see how it runs over time.

Link to comment
Share on other sites

Nice...by the sounds of it your instructions my be a little clearer.

There are 4 settings that you can change (F1-F4 on my unit).

F1 is the desired temperature.

F2 is the variation before cutting in or out.

F3 - not sure.. would like to know what this is for, mine is set on 1

F4 is the calibration variation.

Do you know what F3 is for?

Link to comment
Share on other sites

F3 is the compressor delay time. It basically protects the compressor from switching on again too soon after it switched off. Default on mine was 3 minutes.

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • sdlTBfanUK
      Thats a great photo, beautiful blue bolt, I hope it survived the molt without dropping the eggs! I think I can just about see some black dots (eyes) on the central egg but can't be 100% sure. I used to (and plan to again) do weekly water change of 10-15% but if you do too large or quick (not drip in new water) that would likely trigger a molt. What KH are they in, my new setup is sitting at (and refusing to budge) KH 3 and PH 7.5 so I may have to settle for neocaridina shrimp this time as opposed to the caridina I want, though not looking/deciding just yet, give the tank a bit more of a run in! Tap water here starts at kH 14, tds 320, when filtered goes to KH 0 and PH 6 but when put in the tank keeps going to KH3 and PH 7.5 despite 3 x 50% water changes???? You may be at 'maximum capacity' with only 20L tank especially if the tank is a cube type rather than shallow type?
    • beanbag
      Right now this tank only has blue bolts and golden bee (red bolts?).  The eggs start off all brown, but at the end, I notice that some are kind of a clear pink-ish color.  So I don't know if that is the egg color of dud or golden bee.  Picture of shrimp only about half hour before molting. The water is always RO + remineralizer, so it should be ok. The tank seems to still be on a "good streak" ever since I started the regimen of weekly water change, monthly gravel vac and plant trim.  The point being to keep the amount of waste low and removing moss / floating plants so that the nitrates go towards growing algae.  At one point, I had three berried females, but only netted about half dozen babies by the end, due to this early molting problem.  There might be about 30-40 shrimp total in 5 gallons, but still very few full-sized adults.
    • ngoomie
      Alright, I've done a bit more research on gentian violet's cancer-causing potential but I haven't yet done research on malachite green's to compare. But from reading the California propositon 65 document about GV (North Americans incl. some Canadians will recognize this as the law that causes some products they buy to be labelled with "known to the state of California to cause cancer", including the exact product I bought) it seems that the risk of cancer is related to internal use, either injection or ingestion. Speaking of ingestion, I think GV bans mainly relate to its use in treating fish/shrimp/etc. which are intended for human consumption, because of the above. And in countries where GV isn't banned for this purpose, it does seem to get used on various species of shrimp without causing any issue for the shrimp themselves (at least enough so for shrimp farming purposes). See the following: In February, the FDA Began Rejecting Imported Shrimp for Gentian Violet and Chloramphenicol (2022 article by Southern Shrimp Alliance) FDA Starts New Calendar Year by Refusing Antibiotic-Contaminated Shrimp from Three BAP-Certified Indian Processors and Adding a BAP-Certified Vietnamese Processor to Import Alert (2024 article by Southern Shrimp Alliance) Southern Shrimp Alliance and some other organizations have tons of other articles in this vein, but I'd be here for a while and would end up writing an absolutely massive post if I were to link every instance I found of articles mentioning shrimp shipments with gentian violet and/or leucogentian violet registering as contaminants. That being said, I know shrimp farmed for consumption and dwarf shrimp are often somewhat distantly related (in fact, the one time a shrimp's species name is listed that I can see, it's the prawn sp. Macrobrachium rosenbergii, who at best occupies the same infraorder as Neocaridina davidi but nothing nearer), but this at least gives a slightly better way of guessing whether it will be safe for aquarium dwarf shrimp or not than my bladder snail anecdote from the OP.
    • sdlTBfanUK
      I would hazard a guess that perhaps those eggs were unfertilized and thereby unviable? Did the eggs change colour, usually yellow to grey as the yolks used up, or any eyes in the eggs. Is your water ok, using RO remineralised and the parameters in range, as I have heard others say that if the water isn't good it can 'force' a molt? How is it going overall, do you have a good size colony in the tank, you may have reached 'maximum occupancy' as a tank can only support so many occupants.
    • beanbag
      Hello folks,  The current problem I am having is that my Taiwan bee shrimp are molting before all their eggs have hatched.  Often the shrimp keep the eggs for 40+ days.  During that time, they lose about half or so, either due to dropping or duds or whatever.  Shortly before molting they look to have about a dozen left, and then they molt with about half a dozen eggs still on the shell.  Then the other shirmp will come and eat the shell.  These last few times, I have been getting around 0-3 surviving babies per batch.  I figure I can make the eggs hatch faster by raising the water temperature more (currently around 68F, which is already a few degrees higher than I used to keep it) or make the shrimp grow slower by feeding them less (protein).  Currently I feed Shrimp King complete every other day, and also a small dab of Shrimp Fit alternating days.  Maybe I can start alternating with more vegetable food like mulberry?  or just decrease the amount of food?
×
×
  • Create New...