Jump to content

ADA Amazonia too acidic?


viridisornatus

Recommended Posts

Hello,
I'm using about 5L of ADA Amazonia in about 40 actual litres of water (tank is a 2ft). The water is KH 0-1. The pH is 6 or less (unreadable) according to the API test kit. The soil is about a week old. I was wondering how soon it might buffer above pH 6, or if I remove some of the soil, will it buffer less from the beginning, or will it just keep buffering below 6 and merely exhaust sooner? I want the pH around 6.3 but I don't want to mess with KH. Thanks :)

Link to comment
Share on other sites

17 minutes ago, viridisornatus said:

how soon it might buffer above pH 6

 

You you using tap water? or RO / rainwater?

 

Link to comment
Share on other sites

Melbourne Yan Yean reservoir tapwater for now, RO when I get shrimp :)

Link to comment
Share on other sites

I just did a new test, water comes out of the tap at pH 7.2, KH 0-1.

Link to comment
Share on other sites

Hey guys, the tank is still reading pH 6 or below. I think I've done about 3 complete WC since adding the soil (rescaping mess). I removed about 1 L of soil before last WC. Does anyone know how long it would take this amount of soil to buffer above pH 6 and stay there long term? I understand that startup pH can be extreme.

Thanks :)

Link to comment
Share on other sites

GH is 0-1. Not sure if it's accurate, it's tapwater with a bit of added Mg and Ca sulphates. Kit bottle arrived unscrewed with leakage. 

Link to comment
Share on other sites

Well, your pH might rise a little with more GH in it, or it may not. While it's going through it's cycle, you don't need to add any GH in there, but once it's done cycling, you should retest the the pH and GH after adding a GH remineralizer. (stay clear of any that also add in KH)

 

Not sure what shrimp you plan on keeping, but you'll want ~5 GH for most shrimp.

Edited by Zoidburg
additional info
Link to comment
Share on other sites

Thanks Zoidburg :) I hope to keep TB shrimp. I added the Mg/Ca for the plants in the tank as the tap water here is so soft. I just want the pH a bit above 6 to make it easier on the filter bacteria.

I just ordered a couple yellow pH pens off ebay to see how low the pH really is.

Thanks,

Stefan.

Link to comment
Share on other sites

I got a pH pen yesterday. Soaked overnight in storage solution, made up calibration solutions 4 and 6.9 from powder sachets and bought distilled water (Moores ultrapure refresh) and calibrated as best as I could.

Tank pH is around 5.5. Hard to be exact as the calibration at pH 4 is not the same as at 6.9, a couple degrees off. Have only been topping off water for over a week though, no more WC.

Cheers,

Stefan

Link to comment
Share on other sites

3 hours ago, viridisornatus said:

 

Tank pH is around 5.5. Hard to be exact as the calibration at pH 4 is not the same as at 6.9, a couple degrees off. 

What do you mean?

 

On 12/15/2016 at 0:39 PM, viridisornatus said:

I just want the pH a bit above 6 to make it easier on the filter bacteria.

Dont mess with it, Its not about what you want, Things just have a natural process they have to undergo as said above. And It sounds like your over complicating things or trying to rush shrimp in there. Just be patient.

"Hey guys, the tank is still reading pH 6 or below. I think I've done about 3 complete WC since adding the soil (rescaping mess). I removed about 1 L of soil before last WC. Does anyone know how long it would take this amount of soil to buffer above pH 6 and stay there long term? I understand that startup pH can be extreme."

Just leave it to do its thing, Then when its fully finished cycling and you are actually ready to add shrimp, Start remineralising the water  to your desired parameters before adding it to the tank, Then fix whatever issues youve got. Your changing too many things too be able to know whats going wrong IMO Change one thing at a time, Then watch to see what happens. basically KH exhausts aquasoils ability to lower PH and the harder your water the faster the soil is spent.
Hope this helps 

Edited by Zebra
Link to comment
Share on other sites

I made the calibration fluids using the packets that came with the pH pen. My water volume measurements could have been off or some other user error, or faulty pen, who knows? Either way, if I calibrate the pen to pH 4 in the 4 solution, it will not be 6.9 in the 6.9 solution, and vice versa.

 

It's hard to be patient, but I would also like to figure all the kinks out before adding shrimp. Which I don't plan on doing anytime soon. That's why I hoped someone would have some experience to share on the buffering behaviour of Amazonia. It's only 4L in 40L.

Cheers :)

Link to comment
Share on other sites

22 minutes ago, viridisornatus said:

I made the calibration fluids using the packets that came with the pH pen. My water volume measurements could have been off or some other user error, or faulty pen, who knows? Either way, if I calibrate the pen to pH 4 in the 4 solution, it will not be 6.9 in the 6.9 solution, and vice versa.

Cheap meters can be temperamental, I like to use lab strips.
But I think it doesnt matter what it reads after putting it through the first solution, You are supposed to adjust it with each solution, Some people use a 10.1 or something aswell but its known to have a short shelf life. Im pretty sure from memory the pen can be stored in the  4 solution. 
Do you have a TDS meter? Cause its best to test the water first so you know its 0ppm. or close enough to.

 

22 minutes ago, viridisornatus said:

It's hard to be patient, but I would also like to figure all the kinks out before adding shrimp. Which I don't plan on doing anytime soon. That's why I hoped someone would have some experience to share on the buffering behaviour of Amazonia. It's only 4L in 40L.

Cheers :)

I have pretty good experience with a range of different aquasoils including the old and new amazonia. Yeah it does have a strong buffering capacity, Especially if like said above you have a kh of less then 17ppm. The time it takes to reduce this effect is entirely based on the tds of your water, More specifically KH.

While a tank is cycling and stabilizing ph is going to swing randomly due to various factors like oxygen production by BB etc.  so theres little point in testing it, Just know its going to be quite acidic. 

If you want to learn more about the chemistry side of things, A great introduction to testing in general is monitoring NH4, N02 and N03 as a tank naturally cycles.

 

Edited by Zebra
Link to comment
Share on other sites

Thanks for your help Zebra :)

I don't have a TDS meter yet, I can only go by the info the bottled water brand's site says - steam distilled etc.

So it's a given that the soil will lose buffering capacity over time and KH. Assuming all other parameters are constant, will the loss be linear, or will it drop fast initially, hold steady long term, then exhaust in the end, or some other pattern?

Thanks :)

Link to comment
Share on other sites

 

Yeah it slowly loses it over time. Initially the buffering is alot stronger in the first month or 2. After that you notice a bit more stability, Then it doesnt really noticably change much for years from my experience. 
Measuring GH and KH is OK, But especially with shrimp keeping its a good habit to get into to measure TDS cause if you understand how GH and KH relate to overall tds (Its usually about have the make up of your water) 
Then most of the time the TDS reading is enough and unless its way off the charts you can assume your GH and KH are ok. Say you have a Gh of 17ppm and kh of 53ppm and your tds is spot on 70ppm, That means theres nothinng else really in the water. 17+53=70 so theres not left over numbers if that makes sense. Someone else can probably explain the importance of tds better then me lol
If its been made by evaporating and collecting it will be 0ppm. BUT for the future a tds pen is like $5 and a great investment, They dont need constant calibration like ph meters. less moving parts etc.

Edited by Zebra
Link to comment
Share on other sites

Thanks Zebra, that sounds really promising about the buffering, you've put my mind at ease.

I definitely plan on getting a TDS meter and other essentials before I add shrimp. I've already got a RO filter, just haven't installed it yet.

Thanks very much,

Stefan :)

Link to comment
Share on other sites

I recently won some really cool prizes including a new tds pen. You can have my old one if you want, it still works fine. 

Idk maybe that's a hassle haha and it's easier to buy one off eBay.

But I would like to see my old one put to use by someone.

Edited by Zebra
  • Like 2
Link to comment
Share on other sites

That's really generous of you, thank you. I have a few things I want to get from Newbreedaquatics though and I am thinking of getting the Xiao Mi pen.

  • Like 1
Link to comment
Share on other sites

Yeah that's the pen I won :) Xiao Mi. Really nice tds meter hey, @newbreed aquatics is great. 

All my shrimp have gone mad for their foods. I'm going to order a heap of mineral balls and other stuff from them after the new year.

  • Like 2
Link to comment
Share on other sites

20 hours ago, Zebra said:

But I would like to see my old one put to use by someone

That's the SKF spirit. Well done for being so generous. 

  • Like 3
Link to comment
Share on other sites

Good work @Zebra!! The SKF and Christmas spirit lives on!!

Amazonia takes a good six weeks to cycle, hard to be patient I this hobby but well worth the wait. I have had culls from cherries and TBs thriving in Amazonia for well over eighteen months now. It will sit at lowph,at or below 6 for quite some time,but that's a good thing for Bluebolts and others TB types. 

Let it cycle and all will be well!! 

  • Like 2
Link to comment
Share on other sites

Always good to pay it forward when I get lucky☺️
Can you please send me some info on the food bags you use Jamie  @newbreed They are very nice and I wanted to order some to package dry ferts. Much appreciated mate.
Cheers.

Edited by Zebra
  • Like 2
Link to comment
Share on other sites

What are food bags?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • beanbag
      Update to say that after a few gravel vacs, front wall scrub, moss / floating plant trim, that the condition seems to have improved.  My current theory is that it is due to waste / debris management, where "stuff" like that brown mulm accumulates in the substrate and behind the HMF filters.  Maybe some tanks can somehow deal with it, but mine can't.  Also another experienced shrimper suggested that maybe those "shell bugs" don't just live on the shrimps but also in this debris.  Maybe this is the reason some tanks fail due to "old tank syndrome" where all they need is a good gravel vac? Also, I am guessing that plant trim helps too because now more of the nutrients and light go into growing algae instead of more plants? Well anyway for this tank I will try weekly water change and monthly gravel vac / plant trim.  For my next tank, I'm thinking of something like an under-gravel system where this mulm can fall down and I vac it out.
    • sdlTBfanUK
      Good to have an update and good to hear you are getting shrimplets, so hopefully your colony will continue and you may not get to the point where you have to cull some to stop over population. These type of shrimp only live 12 - 18 months so the adult deaths may be natural? If you have the time I would do weekly 25% water changes, adding the new water via a drip system and do some vacuuming clean of the substrate each week, even if only a different bit each week! See if that helps in a few months and if it does then stick with that regime? It should help reduce any build-ups that may be occuring!
    • beanbag
      Hello again, much belated update: The tank still has "cycles" of 1-2 month "good streaks" where everybody seems to be doing well, and then a bad streak where the short antenna problem shows up again, and a shrimp dies once every few days.  I am not sure what causes things to go bad, but usually over the course of a few days I will start to see more shrimp quietly standing on the HMF filter, and so I know something is wrong.  Since I am not "doing anything" besides the regular 1-2 week water changes, I just assume that something bad is building up.  Here's a list of things that I've tried that are supposed to be "can't hurt" but didn't prevent the problem either: Dose every other day with Shrimp Fit (very small dose, and the shrimp seem to like it) Sotching Oxydator Seachem Purigen to keep the nitrates lower Keeping the pH below 5.5 with peat Things that I don't do often, so could possibly "reset" the tank back to a good streak, are gravel vac and plant trim, so maybe time to try those again. One other problem I used to have was that sometimes a shrimp would suddenly stop eating with a full or partially full digestive tract that doesn't clear out, and then the shrimp will die within a few days.  I suspected it was one of the foods in my rotation - Shrimp Nature Infection, which contains a bunch of herbal plant things.  I've had this in my food rotation for a few years now and generally didn't seem to cause problems, but I removed it from the rotation anyway.  I don't have a lot of adult Golden Bees at this point so I can't really tell if it worked or not. Overall the tank is not too bad - during the good streaks occasionally a shrimp will get berried and hatch babies with a 33-50% survival rate.  So while there are fewer adults now, there are also a bunch of babies roaming around.  I guess this tank will stagger on, but I really do need to take the time to start up a new tank.  (or figure out the problem)
    • jayc
      If that is the offspring, then the parents are unlikely to be PRL. I tend to agree with you. There are very few PRLs in Australia. And any that claim to be needs to show proof. PRL genes have to start as PRL. CRS that breed true after x generations doesn't turn it into a PRL. Neither can a Taiwan bee shrimp turn into a PRL despite how ever many generations. I've never seen a PRL with that sort of red colour. I have on Red Wines and Red Shadows - Taiwan bee shrimps. So somewhere down the line one of your shrimp might have been mixed with Taiwan bees and is no longer PRL. It just tanks one shrimp to mess up the genes of a whole colony. 
    • sdlTBfanUK
      Sorry, missed this one somehow! The PRL look fantastic and the odd ones look part PRL and part Red wine/Red shadow in the colour. They are still very beautiful but ideally should be seperated to help keep the PRL clean if you can do that.  Nice clear photos!
×
×
  • Create New...