Jump to content

Any suggestions for this light


larrymull

Recommended Posts

Hi guys I bought a cube 30x30x30 aquarium and thus ordered a 30cm wide light the other day. I received it today and found out that my tank is actually 31cm across which meant the light was smaller and as you can see in the photo I've just used some wooden sticks to get on by.

My question is does anyone have any good ideas how I can secure this better and make it look more natural?

post-1428-0-65656500-1427100497_thumb.jp

Link to comment
Share on other sites

Heat the legs on the gas stove, and remould the legs making it fit 0.5 cm each side.

Hope those legs are perspex not glass.

Edited by jayc
Link to comment
Share on other sites

I think that's where you need to be creative.

You just need to push them out by 0.5cm each side.

Link to comment
Share on other sites

Just apply the heat then wedge something in between that's 1cm wider than the current gap. One of those bits of wood should cut off just right. 

Link to comment
Share on other sites

OK i'll try tonight, should be interesting! One thing is the gas burning the perplex will probably make it look black and smokey. 

Link to comment
Share on other sites

It shouldn't burn. If it is burning and turning black, you're doing it wrong.

Keep moving it over the heat, and never leave it stationary for too long. Don't stick the plastic into the fire, but rotate it just above the flame.

I have bent perspex tubes over a gas stove just fine, without staining the perspex.

If you have a heat gun, even better. Use that instead.

 

What you want to do is to try to bend the legs out like in the picture below. (apologies for it's simplicity).

 

  _____________

  |                         |

 /                          \

  • Like 1
Link to comment
Share on other sites

Jayc simplicity is the most perfect form of an explanation - I appreciate the diagram. Hopefully I am successful in this operation.

Link to comment
Share on other sites

@jac @2ofus this worked perfectly and it actually looks as good as it did when I bought it. Thank you!!

Link to comment
Share on other sites

That's really good doesn't even look bent. Good work

Link to comment
Share on other sites

Good work !

Now it looks like it was built for that tank.

Heaps better than those pieces of wood.

Link to comment
Share on other sites

  • 1 month later...

Good job on making that custom-fit :jig:

 

Can you tell me what lamp it was?

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • beanbag
      Update to say that after a few gravel vacs, front wall scrub, moss / floating plant trim, that the condition seems to have improved.  My current theory is that it is due to waste / debris management, where "stuff" like that brown mulm accumulates in the substrate and behind the HMF filters.  Maybe some tanks can somehow deal with it, but mine can't.  Also another experienced shrimper suggested that maybe those "shell bugs" don't just live on the shrimps but also in this debris.  Maybe this is the reason some tanks fail due to "old tank syndrome" where all they need is a good gravel vac? Also, I am guessing that plant trim helps too because now more of the nutrients and light go into growing algae instead of more plants? Well anyway for this tank I will try weekly water change and monthly gravel vac / plant trim.  For my next tank, I'm thinking of something like an under-gravel system where this mulm can fall down and I vac it out.
    • sdlTBfanUK
      Good to have an update and good to hear you are getting shrimplets, so hopefully your colony will continue and you may not get to the point where you have to cull some to stop over population. These type of shrimp only live 12 - 18 months so the adult deaths may be natural? If you have the time I would do weekly 25% water changes, adding the new water via a drip system and do some vacuuming clean of the substrate each week, even if only a different bit each week! See if that helps in a few months and if it does then stick with that regime? It should help reduce any build-ups that may be occuring!
    • beanbag
      Hello again, much belated update: The tank still has "cycles" of 1-2 month "good streaks" where everybody seems to be doing well, and then a bad streak where the short antenna problem shows up again, and a shrimp dies once every few days.  I am not sure what causes things to go bad, but usually over the course of a few days I will start to see more shrimp quietly standing on the HMF filter, and so I know something is wrong.  Since I am not "doing anything" besides the regular 1-2 week water changes, I just assume that something bad is building up.  Here's a list of things that I've tried that are supposed to be "can't hurt" but didn't prevent the problem either: Dose every other day with Shrimp Fit (very small dose, and the shrimp seem to like it) Sotching Oxydator Seachem Purigen to keep the nitrates lower Keeping the pH below 5.5 with peat Things that I don't do often, so could possibly "reset" the tank back to a good streak, are gravel vac and plant trim, so maybe time to try those again. One other problem I used to have was that sometimes a shrimp would suddenly stop eating with a full or partially full digestive tract that doesn't clear out, and then the shrimp will die within a few days.  I suspected it was one of the foods in my rotation - Shrimp Nature Infection, which contains a bunch of herbal plant things.  I've had this in my food rotation for a few years now and generally didn't seem to cause problems, but I removed it from the rotation anyway.  I don't have a lot of adult Golden Bees at this point so I can't really tell if it worked or not. Overall the tank is not too bad - during the good streaks occasionally a shrimp will get berried and hatch babies with a 33-50% survival rate.  So while there are fewer adults now, there are also a bunch of babies roaming around.  I guess this tank will stagger on, but I really do need to take the time to start up a new tank.  (or figure out the problem)
    • jayc
      If that is the offspring, then the parents are unlikely to be PRL. I tend to agree with you. There are very few PRLs in Australia. And any that claim to be needs to show proof. PRL genes have to start as PRL. CRS that breed true after x generations doesn't turn it into a PRL. Neither can a Taiwan bee shrimp turn into a PRL despite how ever many generations. I've never seen a PRL with that sort of red colour. I have on Red Wines and Red Shadows - Taiwan bee shrimps. So somewhere down the line one of your shrimp might have been mixed with Taiwan bees and is no longer PRL. It just tanks one shrimp to mess up the genes of a whole colony. 
    • sdlTBfanUK
      Sorry, missed this one somehow! The PRL look fantastic and the odd ones look part PRL and part Red wine/Red shadow in the colour. They are still very beautiful but ideally should be seperated to help keep the PRL clean if you can do that.  Nice clear photos!
×
×
  • Create New...