Jump to content

My el cheapo DIY LED lighting


lorby

Recommended Posts

Thought I might share some of my experiences with DIY LED lighting.

Hey all, thought I might share my el cheapo DIY LED light :D

Start off with a scrap piece of aluminium I found in the shed and clean it up a bit:

30664af9.jpg

15 cree LED's purchased from Dealextreme, $3-4 each. Stuck down with thermal adhesive from DX $6 for 50gm 8 white, 2 green and 5 blue:

023865ed.jpg

Another piece of scrap I took from work, holds 4 green on/off switches and 3 100k potentiometers.

7287a79e.jpg

3 meanwell LDD-700 LED drivers running off a spare dell 20v laptop adapter. Each driver runs 5 LED's with the 20v adapter. They cost $14 each

Here's the finished product running on low. I'll try and get some more pics with everything on full and the blue set of 5 on a new driver (you can't see any blues because the driver died :().

08100ba6.jpg

As you can see, even though I'm only running 2 green's they are quite overpowering.

All dimming is controlled by an arduiono'>http://arduino.cc/]arduiono uno R3 board

This is the little control panel. 1 master switch connected to the DC adapter input. 3 individual switches connected to the dc input to each driver (taken from the master switch). and 3 potentiometers hooked up to the arduino board. The arduino also supplies the regulated 5v DC power to each potentiometer. 1 knob for each driver :).

a873359e.jpg

The mess

931f6e13.jpg

Running on ~20%, didn't want to blind myself while taking the pic!

14b6425f.jpg

Link to comment
Share on other sites

Full tank shots in operation

c5790aa4.jpg4efa6a0c.jpg

Now my next LED light project:

fd2261c0.jpg532e4917.jpg

Made from a whiteboard pen tray they were throwing out at work. Cut 2x 2 foot lenghts and bolted them together for the housing. Running 6 whites, 2 reds and 2 blues, all cree's.

Link to comment
Share on other sites

cool really impressed ... if only I was motivated to do this myself ...

Link to comment
Share on other sites

that is great DIY. i wish i new more about making lights.

the light in the tank looks so clean and bright. do you know what light it creates ?

i use T5HO 10,000k tubes are the leds like this or are they a different type of light?

Link to comment
Share on other sites

Very nice light unit. Can you provide some more info about how you wired it up to the Arduino board? i.e Is it difficult to setup?

I went down the path of the meanwell drivers with a dimming unit.

Link to comment
Share on other sites

Dean: These don't go as high as 10k, but should provide a good spectrum for the plants to use (If I recall they go from around 4-8k). The individual LED's don't provide a bigger spectrum like fluros do, that's why you have to mix the colours. Apparently red and blue leds are the best for plant growth and the whites provide the viewing pleasure :P. Unfortunately I'm missing the reds on this one so I will definitely have to fix that soon! I think green is pretty useless I just wanted to see what the tank would look like with them.

Heavyd: Fancy seeing you on here to :P. I'm hoping to take a look at your shrimp setup tomorrow as well :D. The arduino was a little bit of a learning curve, but I'm on the OCAU computing forums and the guys there were extremely helpful.

Basically the drivers I got have a pin for dimming control by PWM (pulse width modulation, it's like a digital form of dimming). But I need anologue control (the pots on the top with knobs attached) So the arduino has up to 5 anologue inputs, and converts them to a digital PWM code on the outputs using some code that I can provide if you like). IT runs off a 12v AC adapterand has a 5v regulator that I can hook the potentiometers up to.

So the arduino puts 5 volts to the pots > the pots vary that from 0-5v by turning it and send that to an input on the arduino. The arduino copde than says. 0 volts on the input = 0% PWM on the output and 5 volts on the input = 100% PWM on the output. and everything in between.

I hope that makes a teensy bit of sense, I haven't finished my coffee yet :P

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • beanbag
      Update to say that after a few gravel vacs, front wall scrub, moss / floating plant trim, that the condition seems to have improved.  My current theory is that it is due to waste / debris management, where "stuff" like that brown mulm accumulates in the substrate and behind the HMF filters.  Maybe some tanks can somehow deal with it, but mine can't.  Also another experienced shrimper suggested that maybe those "shell bugs" don't just live on the shrimps but also in this debris.  Maybe this is the reason some tanks fail due to "old tank syndrome" where all they need is a good gravel vac? Also, I am guessing that plant trim helps too because now more of the nutrients and light go into growing algae instead of more plants? Well anyway for this tank I will try weekly water change and monthly gravel vac / plant trim.  For my next tank, I'm thinking of something like an under-gravel system where this mulm can fall down and I vac it out.
    • sdlTBfanUK
      Good to have an update and good to hear you are getting shrimplets, so hopefully your colony will continue and you may not get to the point where you have to cull some to stop over population. These type of shrimp only live 12 - 18 months so the adult deaths may be natural? If you have the time I would do weekly 25% water changes, adding the new water via a drip system and do some vacuuming clean of the substrate each week, even if only a different bit each week! See if that helps in a few months and if it does then stick with that regime? It should help reduce any build-ups that may be occuring!
    • beanbag
      Hello again, much belated update: The tank still has "cycles" of 1-2 month "good streaks" where everybody seems to be doing well, and then a bad streak where the short antenna problem shows up again, and a shrimp dies once every few days.  I am not sure what causes things to go bad, but usually over the course of a few days I will start to see more shrimp quietly standing on the HMF filter, and so I know something is wrong.  Since I am not "doing anything" besides the regular 1-2 week water changes, I just assume that something bad is building up.  Here's a list of things that I've tried that are supposed to be "can't hurt" but didn't prevent the problem either: Dose every other day with Shrimp Fit (very small dose, and the shrimp seem to like it) Sotching Oxydator Seachem Purigen to keep the nitrates lower Keeping the pH below 5.5 with peat Things that I don't do often, so could possibly "reset" the tank back to a good streak, are gravel vac and plant trim, so maybe time to try those again. One other problem I used to have was that sometimes a shrimp would suddenly stop eating with a full or partially full digestive tract that doesn't clear out, and then the shrimp will die within a few days.  I suspected it was one of the foods in my rotation - Shrimp Nature Infection, which contains a bunch of herbal plant things.  I've had this in my food rotation for a few years now and generally didn't seem to cause problems, but I removed it from the rotation anyway.  I don't have a lot of adult Golden Bees at this point so I can't really tell if it worked or not. Overall the tank is not too bad - during the good streaks occasionally a shrimp will get berried and hatch babies with a 33-50% survival rate.  So while there are fewer adults now, there are also a bunch of babies roaming around.  I guess this tank will stagger on, but I really do need to take the time to start up a new tank.  (or figure out the problem)
    • jayc
      If that is the offspring, then the parents are unlikely to be PRL. I tend to agree with you. There are very few PRLs in Australia. And any that claim to be needs to show proof. PRL genes have to start as PRL. CRS that breed true after x generations doesn't turn it into a PRL. Neither can a Taiwan bee shrimp turn into a PRL despite how ever many generations. I've never seen a PRL with that sort of red colour. I have on Red Wines and Red Shadows - Taiwan bee shrimps. So somewhere down the line one of your shrimp might have been mixed with Taiwan bees and is no longer PRL. It just tanks one shrimp to mess up the genes of a whole colony. 
    • sdlTBfanUK
      Sorry, missed this one somehow! The PRL look fantastic and the odd ones look part PRL and part Red wine/Red shadow in the colour. They are still very beautiful but ideally should be seperated to help keep the PRL clean if you can do that.  Nice clear photos!
×
×
  • Create New...