Jump to content

How To: DIY Cooling Fan


ShrimpDesigns

Recommended Posts

Over the past month or two I have been gathering information and parts to construct a few cooling fans for my tanks as they house delicate shrimp. This build cost $40 per fan although it could certainly be done for less. Anyway here is how it was put together.

1. Draw up plans so materials can be cut to size later on. Here I used a good quality 80mm fan (Noctua Redux NF-R8 1800rpm). This fan cost $14 although you can get cheaper ones which would probably do a similar job for about half the price.

IMG_20150124_161148_zpsxv1izckm.jpg

IMG_20150124_161156_zpssmpnxiwg.jpg

2. Out of the four wires supplied, the only ones needed were the black and yellow. This meant we had to buy a jack plug which connected to the fan and then an AC/DC 12 volt adaptor.

IMG_20150125_175326_zpsnlxim4fm.jpg

3. Get some clear acrylic cut to size. Once again you can save money here, we had a plastics company do it for us and it cost $57 just for the pieces shown. So if budget is a problem it would be best to buy your own acrylic and cut it yourself.

IMG_20150206_164740_zpsfxbc1qnl.jpg

4. Drill holes so that the screws supplied with the fan can be used to hold the fan to the acrylic. Then, make an adjustable clamp to hold on the side of aquarium using wing nuts and screws.

IMG_20150206_182602_zpsrq5zcvny.jpg

5. Attach to aquarium, plug in and your done!

IMG_20150206_185718_zps85efjvfu.jpg

IMG_20150206_185729_zpspl3jejq5.jpg

A Couple of Things to Remember

- When looking for a fan make sure you get one with low decibels ( under 20 is good ), low RPM ( so it doesn't disturb the water to much and high air flow ( measured in m³/h, mine is 53m³/h to give you an idea

- Pricing per Fan

Fan $14 (MSY)

Acrylic $20 (cut to size)

Wing nuts and Screws $2 (Bunnings)

Adaptors $2 (eBay)

- Overall the fan does the job nicely and consistently brings the temperature down for those hot days.

Thanks for reading,

Louis

  • Like 1
Link to comment
Share on other sites

Amazing! I was exploring a diy pc fans cooling method months back but it was feasible to have my local plastic provider to cut and fabricate. They charged so much per cut and I lacked proper tools.

Great stuff!

Link to comment
Share on other sites

Amazing! I was exploring a diy pc fans cooling method months back but it was feasible to have my local plastic provider to cut and fabricate. They charged so much per cut and I lacked proper tools.

Great stuff!

Thanks mate, you could go out and buy some tools but it would probably end up the same cost and wouldn't have an as slick finish.

Link to comment
Share on other sites

  • 5 months later...

Had to add my own design to this post because it's inspired me so much.

Nothing like OP's design but I managed to keep my cost significantly lower.

DSCF3631.EbiFanHQ_zpsrtw1nv3h.jpg

DSCF3635.EbiFanHQ_zpsml1l4v7j.jpg

DSCF3637.EbiFanHQ_zpshwhqzq9q.jpg

DSCF3632.EbiFanHQ_zpsc6rxyeic.jpg

This fan has a Low - High speed mode. I Wanted to do something like this because I wanted to option to fit this fan on small (4gal) - large (20L) tanks. 

Edited by ShrimpFan
  • Like 1
Link to comment
Share on other sites

Had to add my own design to this post because it's inspired me so much.

Nothing like OP's design but I managed to keep my cost significantly lower.

DSCF3631.EbiFanHQ_zpsrtw1nv3h.jpg

DSCF3635.EbiFanHQ_zpsml1l4v7j.jpg

DSCF3637.EbiFanHQ_zpshwhqzq9q.jpg

DSCF3632.EbiFanHQ_zpsc6rxyeic.jpg

This fan has a Low - High speed mode. I Wanted to do something like this because I wanted to option to fit this fan on small (4gal) - large (20L) tanks. 

 

Very nice. May I ask where did you get the mounting clip for the fan? Clean and simple. Both OP and yours look really nice. Thanks for sharing.

Link to comment
Share on other sites

I got the clip at a local plastics shop. I'm not sure if you have anything similar to that if you're located in Australia as I am in America. I had to use a heat gun to heat up the plastic and stretch it to fit the thickness of the rimless tanks. Works really well and sturdy. 

Link to comment
Share on other sites

Shrimp Fan made a fan for shrimp. LOL!

Very clever and yet so simple. 

Edited by jayc
Link to comment
Share on other sites

Shrimp Fan made a fan for shrimp. LOL!

Very clever and yet so simple.

LOL! It's funny. I didn't catch the irony until now! :5565bf0371061_D:

  • Like 1
Link to comment
Share on other sites

  • 4 weeks later...

I got the clip at a local plastics shop. I'm not sure if you have anything similar to that if you're located in Australia as I am in America. I had to use a heat gun to heat up the plastic and stretch it to fit the thickness of the rimless tanks. Works really well and sturdy. 

Could you possible ask the plastics store what the intended use is so I could ask one here :D

Link to comment
Share on other sites

I have to add my own diy aswell lol 

very very very efficient and also cost less then $15 :) 

 

down fall .... Plenty of evaporation :( 

but 1000x's more efficient then pc fans 

 

Take off the bottom section (normally unscrews in the centre of the neck) 

and simply place on top of tank :) 

(you can also freeze wet/damp

tea towels/towels) 

 

Common pedestal fan

1,000,000x's faster then pc fans 

have your pre aged water handy as it will evaporate a fair bit  :) 

enjoy 

image.jpg

Edited by 2OFUS
  • Like 2
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • beanbag
      Update to say that after a few gravel vacs, front wall scrub, moss / floating plant trim, that the condition seems to have improved.  My current theory is that it is due to waste / debris management, where "stuff" like that brown mulm accumulates in the substrate and behind the HMF filters.  Maybe some tanks can somehow deal with it, but mine can't.  Also another experienced shrimper suggested that maybe those "shell bugs" don't just live on the shrimps but also in this debris.  Maybe this is the reason some tanks fail due to "old tank syndrome" where all they need is a good gravel vac? Also, I am guessing that plant trim helps too because now more of the nutrients and light go into growing algae instead of more plants? Well anyway for this tank I will try weekly water change and monthly gravel vac / plant trim.  For my next tank, I'm thinking of something like an under-gravel system where this mulm can fall down and I vac it out.
    • sdlTBfanUK
      Good to have an update and good to hear you are getting shrimplets, so hopefully your colony will continue and you may not get to the point where you have to cull some to stop over population. These type of shrimp only live 12 - 18 months so the adult deaths may be natural? If you have the time I would do weekly 25% water changes, adding the new water via a drip system and do some vacuuming clean of the substrate each week, even if only a different bit each week! See if that helps in a few months and if it does then stick with that regime? It should help reduce any build-ups that may be occuring!
    • beanbag
      Hello again, much belated update: The tank still has "cycles" of 1-2 month "good streaks" where everybody seems to be doing well, and then a bad streak where the short antenna problem shows up again, and a shrimp dies once every few days.  I am not sure what causes things to go bad, but usually over the course of a few days I will start to see more shrimp quietly standing on the HMF filter, and so I know something is wrong.  Since I am not "doing anything" besides the regular 1-2 week water changes, I just assume that something bad is building up.  Here's a list of things that I've tried that are supposed to be "can't hurt" but didn't prevent the problem either: Dose every other day with Shrimp Fit (very small dose, and the shrimp seem to like it) Sotching Oxydator Seachem Purigen to keep the nitrates lower Keeping the pH below 5.5 with peat Things that I don't do often, so could possibly "reset" the tank back to a good streak, are gravel vac and plant trim, so maybe time to try those again. One other problem I used to have was that sometimes a shrimp would suddenly stop eating with a full or partially full digestive tract that doesn't clear out, and then the shrimp will die within a few days.  I suspected it was one of the foods in my rotation - Shrimp Nature Infection, which contains a bunch of herbal plant things.  I've had this in my food rotation for a few years now and generally didn't seem to cause problems, but I removed it from the rotation anyway.  I don't have a lot of adult Golden Bees at this point so I can't really tell if it worked or not. Overall the tank is not too bad - during the good streaks occasionally a shrimp will get berried and hatch babies with a 33-50% survival rate.  So while there are fewer adults now, there are also a bunch of babies roaming around.  I guess this tank will stagger on, but I really do need to take the time to start up a new tank.  (or figure out the problem)
    • jayc
      If that is the offspring, then the parents are unlikely to be PRL. I tend to agree with you. There are very few PRLs in Australia. And any that claim to be needs to show proof. PRL genes have to start as PRL. CRS that breed true after x generations doesn't turn it into a PRL. Neither can a Taiwan bee shrimp turn into a PRL despite how ever many generations. I've never seen a PRL with that sort of red colour. I have on Red Wines and Red Shadows - Taiwan bee shrimps. So somewhere down the line one of your shrimp might have been mixed with Taiwan bees and is no longer PRL. It just tanks one shrimp to mess up the genes of a whole colony. 
    • sdlTBfanUK
      Sorry, missed this one somehow! The PRL look fantastic and the odd ones look part PRL and part Red wine/Red shadow in the colour. They are still very beautiful but ideally should be seperated to help keep the PRL clean if you can do that.  Nice clear photos!
×
×
  • Create New...