Jump to content

DIY Filter Guard


CNgo2006

Recommended Posts

Hey Guys,

I came across I great DIY Video so thought I would share how I make my own filter guards...These can be made to fit any size tubing at the fraction of the cost of what is sold and is so very easy to make. So lets get started!

Note: It is recommended that you use protective goggles and gloves, as frayed mesh wires can get pretty sharp.

Here is what you will need to make the filter guard:

*Stainless Steel Mesh sheet hole size #30 (can be purchased at the mesh company online, I got the A3 size sheet which is enough for a lot of guards!)

*Tin snips

*Heat Shrink (depending on the size of your tube get the heat shrink at least 5mm bigger, can be purchased eBay)

*Heat source (Lighter, hair dryer, heat gun, etc)

*A tube of the size required

*Pencil, marker

*Ruler

*Cable ties

*Craft knife

IMAG0165-1.jpg

Steps

Prepare cable ties as you will need both hands free

IMAG0167.jpg

Cut mesh sheet to size depending on how long you want the guard and how thin the tube is (I cut mine 10cmx10cm) and wrap tightly around the tube, secure tightly with cable ties

IMAG0168.jpg

Cut another piece of mesh depending on the width of the mesh wrapped around tube (mine was 18mm), cut a square piece (18x18mm), place on end of mesh and bend corners over

IMAG0174.jpg

Cut a bit of heat shrink (mine was 2cm) and place over the mesh making sure the piece of mesh covering the end stays in place, leave about 0.5cm above.

IMAG0175-1.jpg

Using the heat source you are using (I just used a lighter) and heat the heat shrink until it shrinks tightly around the mesh (make sure you don't heat the same place for too long as it will melt! Just quickly run the flame over the shrink) and then quickly push the end down on a flat surface for a minute.

IMAG0177-1.jpg

The outcome should be something like this (you can use the craft knife to make the opening bigger if you wish)

IMAG0178.jpg

Now for the other end, repeat the steps above but shove the tube in instead. Leave for a minute or so.

IMAG0173.jpg

Remove the tube and cut the cable ties, cut a thin bit of heat shrink to place in middle of guard for extra support, heat it until tight. And there you have it, your DIY filter guard.

IMAG0179-1.jpg

For a fraction of the cost you can make all the filter guards needed, can be HOB, canister, overflow pipe, etc. for your 20 shrimp tanks!:encouragement:

If you like this then please thank or like the post!

Cheers Chi.

  • Like 3
Link to comment
Share on other sites

I have one bought that looks identical to that. Good work Chi, saved me some $$ maybe make a few and always have them available to skfer

Link to comment
Share on other sites

Awesome write up Chi, so simple & so effective, excellent work dude :encouragement:

Link to comment
Share on other sites

Thanks guys...thought I would share as this can be done by anyone and if like me don't have too much cash lying around have to DIY to save so we can actually buy the shrimp we want! LOL! For the price of one purchased from LFS I can make at least 5 of these!

Link to comment
Share on other sites

Great informative DIY post.... very easy to follow! :encouragement:

Link to comment
Share on other sites

Well done Chi, well written, and great info ! You've indeed raised the DIY level .......can't wait for your next DIY post ! :applause:

Link to comment
Share on other sites

Great post ty chi :)

Would you mind sharing the people you brought from on ebay please :) Then we will know their reliable :).

I think even if you only have 1 filter running would come in handy to make one of these, if your like me i have moss always getting stuck to my cover and growing on it so would be good to just replace it whilst i clean the other :)

Link to comment
Share on other sites

The mesh is purchased from the mesh company http://www.themeshcompany.com/acatalog/Stainless_Steel_Woven_Wire_A3_Sheets.html they are having a sale buy 2 sheets receive a third free! So get a #30 for the filter guards and a #10 for moss tying and get another 1 of those free, the heat shrink all depends on the size of your filter inlet so it may not be same as mine plus it is only few bucks for a meter, just remember to get it around 5mm bigger than your inlet pipe.

Link to comment
Share on other sites

Cheers Chi...Thanks for the informative guide by using good illustrations (step by step)....:)

Link to comment
Share on other sites

The mesh is purchased from the mesh company http://www.themeshcompany.com/acatalog/Stainless_Steel_Woven_Wire_A3_Sheets.html they are having a sale buy 2 sheets receive a third free! So get a #30 for the filter guards and a #10 for moss tying and get another 1 of those free' date= the heat shrink all depends on the size of your filter inlet so it may not be same as mine plus it is only few bucks for a meter, just remember to get it around 5mm bigger than your inlet pipe.

I just had issues with the buy 2 get one free thing, so i emailed them and they just said order 2 and they'll just throw in the 3rd. So if anyone else encounters the same problem I did (the cart wont apply the discount) just order 2 and drop them an email :)

Link to comment
Share on other sites

Chi, what a great write-up!

The end product looks professionally made. Have you found your new calling?

Link to comment
Share on other sites

I just had issues with the buy 2 get one free thing' date=' so i emailed them and they just said order 2 and they'll just throw in the 3rd. So if anyone else encounters the same problem I did (the cart wont apply the discount) just order 2 and drop them an email :)[/quote']

Thanks for letting us know! I remember I ordered 2 differeent sizes and they just chucked in a 3rd of whichever so if you want a specific #size (as long as the 2 ordered are same price or it will be the cheaper of the 2 that they send free) email them like torface said!

Link to comment
Share on other sites

Chi' date=' what a great write-up!

The end product looks professionally made. Have you found your new calling?[/quote']

LOL! Maybe, maybe. What you talking about Doron everything I make is professional looking! LOL!

Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • beanbag
      Update to say that after a few gravel vacs, front wall scrub, moss / floating plant trim, that the condition seems to have improved.  My current theory is that it is due to waste / debris management, where "stuff" like that brown mulm accumulates in the substrate and behind the HMF filters.  Maybe some tanks can somehow deal with it, but mine can't.  Also another experienced shrimper suggested that maybe those "shell bugs" don't just live on the shrimps but also in this debris.  Maybe this is the reason some tanks fail due to "old tank syndrome" where all they need is a good gravel vac? Also, I am guessing that plant trim helps too because now more of the nutrients and light go into growing algae instead of more plants? Well anyway for this tank I will try weekly water change and monthly gravel vac / plant trim.  For my next tank, I'm thinking of something like an under-gravel system where this mulm can fall down and I vac it out.
    • sdlTBfanUK
      Good to have an update and good to hear you are getting shrimplets, so hopefully your colony will continue and you may not get to the point where you have to cull some to stop over population. These type of shrimp only live 12 - 18 months so the adult deaths may be natural? If you have the time I would do weekly 25% water changes, adding the new water via a drip system and do some vacuuming clean of the substrate each week, even if only a different bit each week! See if that helps in a few months and if it does then stick with that regime? It should help reduce any build-ups that may be occuring!
    • beanbag
      Hello again, much belated update: The tank still has "cycles" of 1-2 month "good streaks" where everybody seems to be doing well, and then a bad streak where the short antenna problem shows up again, and a shrimp dies once every few days.  I am not sure what causes things to go bad, but usually over the course of a few days I will start to see more shrimp quietly standing on the HMF filter, and so I know something is wrong.  Since I am not "doing anything" besides the regular 1-2 week water changes, I just assume that something bad is building up.  Here's a list of things that I've tried that are supposed to be "can't hurt" but didn't prevent the problem either: Dose every other day with Shrimp Fit (very small dose, and the shrimp seem to like it) Sotching Oxydator Seachem Purigen to keep the nitrates lower Keeping the pH below 5.5 with peat Things that I don't do often, so could possibly "reset" the tank back to a good streak, are gravel vac and plant trim, so maybe time to try those again. One other problem I used to have was that sometimes a shrimp would suddenly stop eating with a full or partially full digestive tract that doesn't clear out, and then the shrimp will die within a few days.  I suspected it was one of the foods in my rotation - Shrimp Nature Infection, which contains a bunch of herbal plant things.  I've had this in my food rotation for a few years now and generally didn't seem to cause problems, but I removed it from the rotation anyway.  I don't have a lot of adult Golden Bees at this point so I can't really tell if it worked or not. Overall the tank is not too bad - during the good streaks occasionally a shrimp will get berried and hatch babies with a 33-50% survival rate.  So while there are fewer adults now, there are also a bunch of babies roaming around.  I guess this tank will stagger on, but I really do need to take the time to start up a new tank.  (or figure out the problem)
    • jayc
      If that is the offspring, then the parents are unlikely to be PRL. I tend to agree with you. There are very few PRLs in Australia. And any that claim to be needs to show proof. PRL genes have to start as PRL. CRS that breed true after x generations doesn't turn it into a PRL. Neither can a Taiwan bee shrimp turn into a PRL despite how ever many generations. I've never seen a PRL with that sort of red colour. I have on Red Wines and Red Shadows - Taiwan bee shrimps. So somewhere down the line one of your shrimp might have been mixed with Taiwan bees and is no longer PRL. It just tanks one shrimp to mess up the genes of a whole colony. 
    • sdlTBfanUK
      Sorry, missed this one somehow! The PRL look fantastic and the odd ones look part PRL and part Red wine/Red shadow in the colour. They are still very beautiful but ideally should be seperated to help keep the PRL clean if you can do that.  Nice clear photos!
×
×
  • Create New...