Jump to content
  • Similar Content

    • NoGi
      By NoGi
      Creating a new article is pretty easy. Go to the library section you would like the new article created and click on the "Add new article" button:

      Fill in all the sections and hit save. Your screen will look a little different to the screenshot below as some of the options you see here are only available to the mods.

      If you are writing the article in something else such as MS Word and pasting it in, it's best to save all the formatting for here. When you paste in the content, it's important to remove all the associated formatting. This is done to ensure that all the library articles remain consistent in look and feel. It also saves a lot of rework if the forum font/style ever changes. By sticking to the default forum font and style, articles will automatically be upgraded if there are any changes in the future.

      You can also select the text and use this button to clear the formatting if you are going back to edit an existing article:

    • OzShrimp
      By OzShrimp
      I utilised this method when moving house last January. I have given this as advice on the forum previously a long time ago but not written as an article. Unfortunately i didn't take photos because i was moving house but i have obtained images of the main items required and done an image in paint to explain the holes. i hope this will suffice?.
      You will require:
      20 litre bucket with lid (Source from bunnings or masters) Sponge filter I recommend the ones which have suction caps and a minimum of two if you go for single sponge. Optimum at least 2 dual sponge filters Battery operated air pump. Air hose Drill or sharp pointed object. Excess plants (the more the better) pH buffering substrate. Preparation
      Step 1: Ensure your sponge filters are running on your existing tank for as long as possible to ensure you have beneficial bacteria culture growing on the filters. The longer they are running the better.
      Step 2: Take the lid from your bucket and make holes in the lid. The holes should be big enough for your air hose to fit through one of the holes and I did the extras to ensure new air was able to enter the bucket. Mine was done in a similar pattern to this

      Step 3: Add existent tank water to the bucket. I would recommend at least 3 quarters full as if you are unfortunate enough to suffer an ammonia spike etc (worst case) the more water the lower the impact in theory. Be mindful of how much you add due to holes in the lid, the more the water the more chance of spillage.
      Step 4: Add some of your existing substrate to the bottom of the bucket. I used benibachi for the ph buffering ability which had already been in my tank. I felt it would assist in reducing stress due to resembling the tank.
      Step 5: You want to add the sponge filters to the inside of the bucket and thread your air hose through the holes in the lid.
      Step 6: Add any plants you have available to your bucket. The aim of the plants is to assist the bacteria on the sponge filters in maintaining healthy water due to the small amount. I utilised needle leaf java fern and it also provides a food source for the shrimp.
      Step 7: Add your shrimp and turn on the sponge filters and replace the lid on the bucket.
      Step 8: Store the bucket out of direct sunlight during travel and storage at arriving destination to prevent major fluctuations in water temperature.
      I had approximately 5 CBS inclusive of shrimplets in a bucket utilising this method alive for close to two weeks. They survived 8 hour car trip and then about 12 days whilst my tank cycled being set up in the new house with temperatures averaging over 35 degrees a day.
      TIPS: Prepare your sponge filters in the tank and have them running for as long as possible prior to transfer.
      The later you leave your shrimp to be added to the bucket the better.
      Keep your bucket out of direct sunlight to avoid over heating and mass fluctuations in water temperature.
      Avoid over feeding your shrimp as you dont want an ammonia spike from left over food. Depending on amount of plants these should be sufficient to supply micro organisms to feed on the leaves.
      Battery air pumps are also able to be used in a black out so dont throw them away.


  • Must Read SKF Articles

  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Posts

    • jayc
      +1 for the sponge. 
    • Crabclaw
      Definitely go the sponge. 
    • DEL 707
      I'm no expert, but 1 does seem a fair bit "chunkier" then the rest. Got a bit of a new problem though. I saw 1 of the shrimp cleaning away near the filter intake grill last night. He did look like he might have just been small enough to slip through. I was thinking of buying some filter sponge to jam behind the grill to stop them getting in.
    • Crabclaw
      That’s a cool idea! I would be interested in testing that out as well at some point. Let us know if you try it!
    • sdlTBfanUK
      We don't get the heat you do their but I am planning to get a cooler, a fan when we get to spring if the shrimps do well. I don't know whether that type of cooler is available where you are and it may not be powerful enough anyway. I will just put it on the tank when needed, but thats unlikely to be often here, and so  easy to set up. Obviously this isn't any good where you are based but I wanted to show an alternative to the chiller in case that suits? https://www.pro-shrimp.co.uk/aquarium-coolers/3100-jbl-cooler-200-aquarium-cooler-4014162604293.html?search_query=cooler&results=8  Believe me when I say you don't want to go through the heartache of cooked shrimps, I am still gutted 6 months later and the new lot will never be the same???? CO2 and shrimps is very risky and so I wouldn't use it, especially if it isn't needed and everything is ok? Simon
×
×
  • Create New...