Jump to content
Sign in to follow this  
jc12

How to select a chiller - A simple 3 step guide

Recommended Posts

jc12

We are blessed with a beautiful climate here in Australia, arguably mild summer and winter seasons compared to other continents around the world. However, we experience the infrequent heat waves and harsh summer days which inevitably require hobbyists who keep heat sensitive shrimps to explore cooling options for their tanks, perhaps more so for those living in the warmer regions. Shrimps require a consistent environment to flourish and temperature is one of such parameters that can be easily controlled with a chiller.

 

Step 1: Determine the total water volume to be cooled

This is simply a measurement of your total water volume to be cooled. Please remember to include the water volume of the sump if your system runs on one.

Most tanks are rectangular or cubic shape so a simple Length x Width x Height measurement will suffice.

Example: For a 4’ x 18” x 18” tank,

120cm (L) x 45cm (W) x 45cm (H) = 243,000 cm3 = 243,000 ml = 243L

 

Step 2: Select a chiller based on total water volume to be cooled

Chillers are usually rated to cool a specific volume of water to a set temperature below ambient air temperature. Simply select a chiller that is rated to cool the water volume calculated in Step 1.

The general rule of thumb is to consider a chiller that is one size larger than what you require in order to be energy efficient. A chiller works a lot harder if it kicks in frequently. Selecting a larger chiller that kicks in less often can save you money in the long run.

Example: With reference to the example in Step 1,

(a)   Hailea HC-100A is rated for 50L to 220L*.

(b)   Hailea HC-130A is rated for 50L to 300L*.

(c)   Hailea HC-150A is rated for 50L to 400L*.

Based on the above specifications, the HC-100A would not be adequate for our purpose.

While the HC-130A is rated appropriately and adequate to cool 243L, I would select the HC-150A following the general rule of thumb to go one size larger.

The efficiency of a chiller is affected by a number of factors ranging from ambient conditions, physical location of the chiller, flow rate, whether the air filter has been kept clean, etc.

It is also dependent on the cooling requirements to your specific environment. If you live in a very warm region and you would like to cool your tank 15 or 20 degrees Celsius lower than your ambient air temperature, you might have to consider a chiller that is two sizes larger.

 

Step 3: Select the appropriate flow rate to drive the selected chiller

The appropriate flow rate to drive the selected chiller is an important consideration.

If the flow rate is too slow, the water within the chiller gets cooled too quickly and the thermostat switches the chiller off. Warm water then enters the chiller triggering it to kick in again within a short period of time. This is not energy efficient and frequent kicking in of the compressor would result in more wear and tear.

If the flow rate is too fast, the water flows through the chiller too quickly to be cooled effectively. The chiller takes a longer time to cool the water in the tank, which is also not very energy efficient.

Example: With reference to Step 1 and Step 2, the Hailea HC-150A has a recommended flow rate of 250lph to 1,200lph*.

We need to consider a few things before we can decide the appropriate flow rate for the Hailea HC-150A. This depends on how you would like to drive the chiller. Below are 3 typical scenarios on how most hobbyists would drive their chillers.

Canister filter

A canister filter’s flow rate is usually rated without any filtration media (i.e. an empty canister) or without taking into account any inline equipment (e.g. inline heater, UV, pre-filter, CO2 diffuser, etc.). If you plan to have other equipment connected inline to your canister filter, I would recommend getting a canister filter that is rated on the higher side of the chiller’s recommended flow rate. Also, as the canister filter gets cycled and matures, dirty filtration media, hoses and pipes would also reduce the flow rate. In this instance, I would recommend getting a canister filter rated at 800 lph to 1,200 lph.

Sump

If you are planning to drive your chiller from a sump pump, you could potentially select a sump pump that is higher in flow than what is recommended for the chiller. The flow rate through the chiller can be easily adjusted by teeing off from the sump pump and controlled using a valve. This also allows you to ‘future proof’ your design if you should add more equipment in future (e.g. fluid reactors, UV, etc.). In this instance, I would recommend getting a sump pump of 1,200 lph to 2,000 lph, factoring in other considerations like pressure head, hose/pipe diameter, etc.

Dedicated pump

If you should elect to drive the selected chiller with a dedicated pump, with no intention of connecting any other inline equipment, I would recommend selecting a flow rate that is slightly above the mid-range of the chiller’s recommended flow rate. In this case, I would select a dedicated pump of around 800 lph. A dirty impellor would have a slower flow rate so it is recommended to clean your pump impellor periodically.

A few tips:

  • Locate the chiller in a cool location away from direct sun. Do not enclose the chiller in a confined space (e.g. in the aquarium cabinet) without proper ventilating devices (e.g. exhaust fans, etc).
  • Clean the air filter of the chiller (if applicable).
  • Connect your chiller as the last piece of equipment before the water is returned back to the tank. You would want filtered clean water to be passing through the chiller as it is easier to clean canister filters, sump pumps or dedicated pumps than it is to flush out a dirty chiller.

*Specifications are taken from Hailea website (http://www.hailea.com/e-hailea/index.htm) as at 21 December 2015.


View full article

Share this post


Link to post
Share on other sites
Kingo

Great,  no nonsense points with consideration for additional items that the newer aquarist (like myself) would not/had not considered - fluid reactors, UV along the flow line. I can see now why sumps and racks are actually a cheaper alternative once you have multi tanks...

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  



  • Must Read SKF Articles

  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Posts

    • jayc
      Ahhh ... the age old question of how to trigger your shrimp to breed. We will have to assume you have at least 1 male. What are you feeding them? Feed frozen bloodworms twice a week. The additional protein will give them more energy. Add more Indian Almond Leaves (aka Cattapa leaves) to the tank to promote more tannins and biofilm. Try raising temps to 23C or 74F. A 10% water change might help the females moult.
    • jayc
      No it won't have all the minerals needed for plants. SS GH/KH+ is made up of Calcium carbonate, Magnesium.   Anubias is a slow growing plant, so it does not need much fertilisers. Mosses will grow with out any added ferts. Hairgrass and whatever you have in the back corner will survive without added ferts. Give it CO2 while your tanks is empty of shrimps.    Aim for 4-6 GH.  
    • Newday
      Hello, again.  I really appreciate everyone's wisdom on this topic.  Since I last posted, I lost my 29 gallon tropical freshwater aquarium to a sudden leak. 😞  Thankfully, I was able to save and rehome all the fish.  But, that means my 7 gallon shrimp tank received an upgrade wrt live plants and gravel.  I was hoping that would inspire some mating behavior, but I actually witnessed a female discharging what must be unfertilized eggs just this evening.  The male shrimp (I thought I had two, but now I'm questioning the other's sex after some weeks) is not doing his job and I can't figure out why.  I had to siphon out 50% of the water to move it from it's prior location beneath the 29 gallon.  I have not performed another water change in the nearly 3 weeks since the leak happened.  I check the parameters in the 7 gallon once a week and ammonia, nitrate, and nitrite are 0ppm.  Temp remains at a steady 72 degrees.  The shrimp are as active as ever but that male is unexcited by a tank full of females.  No clue what to do next.😑
    • DEL 707
      I'm thinking of ordering that "Salty Shrimp - Shrimp Mineral GH/KH+". My only concern is, does it also have all the needed minerals for my plants? Edit - If I was to use my tap water, what kind of GH should I be aiming for?
    • sdlTBfanUK
      WOW, that's hard water all right! Amazing how different it is to mine as probably only about 25 miles between us???? You were right to use RO water so at least you have a good starting point from here in! The PH may be the biggest issue as remineralising with a shrimp specific GH/KH+ will sort everything else with RO water. Cherry shrimps are pretty tough and adaptable so will tolerate PH below 7 but the nearer you can get to 7 the better, and a long time acclimating the shrimps using a dripper (there is a tube with regulator sold by ProShrimp for about £10 I think if you don't already have something) will be needed! The soil will take longer to loose its PH buffering ability with the RO though! There are a number of ways you can go from here: 1) RO water plus a GH/KH+ and try to get the PH up somehow although you will be fighting the Soil until that exhausts its buffering ability. 2) You could mix RO and (dechlorinated) tap water at 3:1 and then use a GH+. I do a 50/50 'similar' (half tap water, half brita filtered water) on my oldest tank. can't even remember why but I believe in 'don't try and fix it if it isn't broken' so have just carried on ever since. The mixed water would start at PH 6.2, TDS 70(ish), GH just over 4, KH just under 4 and then you can mineralise it (GH+ only) for the rest. This will exhaust the soil buffering quicker than 1 above and you will save a bit on RO water, use less (about half as much) mineraliser etc. You may think this is a bit too fussy a route though, and the soil will still buffer anyway, just not for as long as all RO water, and when it stops buffering you will have a PH closer to the ideal for the shrimps. Probably where you are now I would just get the snails for now until you have stopped adjusting the water or at least decided where next, probably not much longer before you get shrimps. I would also try turning off the CO2 and just see if it is really needed, if it looks like it is you can easily turn it back on then, but shrimps will do better without it and it MAY not be needed, same for fertilisers??? At least you are doing all this before getting the shrimps, very smart as most of us have learnt the hard/wrong way................ Simon
×
×
  • Create New...