Jump to content

Help please with tank construction questions


Noel

Recommended Posts

I plan to build multiple glass tanks for a tank rack and have no previous experience. Each tank will have length x width x height measurements equal to 45cmx20cmx30cm 

Each tank will be constructed with its side panes on top of the base plane. The rear pane (one of the two shorter side panes) will have a hole drilled into it to accommodate a bulkhead.

I would appreciate advice with the following:

1.    Is 6mm glass all round necessary because of the bulkhead, or can I go thinner?

 

2.    Should the longer side panes span the length of the tank and the shorter panes fit inside them or would it be stronger for the bulkhead if the shorter panes span the width of the tank and the longer sides fit inside them?

 

3.    I have read elsewhere that the inside panes should be cut to a size to allow for an silicone fillet of depth 1mm or more between the panes depending on the tank size and that this provides the structural seal while the silicone inside the tank protects this seal. What fillet depth should I allow for?

Edited by Noel
one sentence did not make sence
Link to comment
Share on other sites

  • 1 month later...

1) I wouldn't go any thinner than 6mm glass.

2)  the shorter panes span the width of the tank and the longer sides fit inside them

3) 1mm depth should be enough for the size of tanks you are planning.

Link to comment
Share on other sites

What he said. If you plan on taking macro photos don't go too thick either. I've got 10mm thick glass which causes too me refraction for my macro lens to get the sort of macro shots I get on my smaller tanks with 6mm glass.

Link to comment
Share on other sites

Just some advice when building either the rack or the tanks leave enough space to enable to insult your tanks with polystyrene sheeting, or similar, on the back of the tank and sides, mainly for winter I also place a cut to size sheet on top of the tanks at lights out.

In summer you can store these cut offs in your roof, a little more insulation in the roof for summer. 

I remove the side sheets in summer to allow for air circulation around the tanks as I have a ceiling fan to help with cooling. I leave the back sheets on as I have sceneries glued on them from my fish keeping days.

Link to comment
Share on other sites

5 hours ago, zn30 said:

leave enough space to enable to insult your tanks with polystyrene sheeting

HAHA, I just saw this. 

 

Insult your tanks. I'd like to see a vid of you doing that!!

 

 

Link to comment
Share on other sites

4 hours ago, jayc said:

HAHA, I just saw this. 

Insult your tanks. I'd like to see a vid of you doing that!!

LOL spell check we just rely on it too much.

However I'm sure we have all insulted our tanks every now and then, and wow and behold anyone standing by giving advice, as my wife shakes her head and glares at me.

Link to comment
Share on other sites

LOL AHAHAHAHAH

 

Polystyrene insults tank.

  • Like 1
Link to comment
Share on other sites

Just don't forget to give your tank the sheets!

image.jpeg

  • Like 2
Link to comment
Share on other sites

Noel, I've just seen this thread. Did you build the tanks yet? One critical factor that nobody mentioned is that the base should be floating between the sides, not supporting them as you described. If you've already built them, well you might be ok because they're small and there's no real structural stress. Good luck! But for future reference, that is not the way to build a glass aquarium. I'm sure there's plenty of online resources that illustrate the right way. 

  • Like 2
Link to comment
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
  • Join Our Community!

    Register today, ask questions and share your shrimp and fish tank experiences with us!

  • Must Read SKF Articles

  • Posts

    • beanbag
      Update to say that after a few gravel vacs, front wall scrub, moss / floating plant trim, that the condition seems to have improved.  My current theory is that it is due to waste / debris management, where "stuff" like that brown mulm accumulates in the substrate and behind the HMF filters.  Maybe some tanks can somehow deal with it, but mine can't.  Also another experienced shrimper suggested that maybe those "shell bugs" don't just live on the shrimps but also in this debris.  Maybe this is the reason some tanks fail due to "old tank syndrome" where all they need is a good gravel vac? Also, I am guessing that plant trim helps too because now more of the nutrients and light go into growing algae instead of more plants? Well anyway for this tank I will try weekly water change and monthly gravel vac / plant trim.  For my next tank, I'm thinking of something like an under-gravel system where this mulm can fall down and I vac it out.
    • sdlTBfanUK
      Good to have an update and good to hear you are getting shrimplets, so hopefully your colony will continue and you may not get to the point where you have to cull some to stop over population. These type of shrimp only live 12 - 18 months so the adult deaths may be natural? If you have the time I would do weekly 25% water changes, adding the new water via a drip system and do some vacuuming clean of the substrate each week, even if only a different bit each week! See if that helps in a few months and if it does then stick with that regime? It should help reduce any build-ups that may be occuring!
    • beanbag
      Hello again, much belated update: The tank still has "cycles" of 1-2 month "good streaks" where everybody seems to be doing well, and then a bad streak where the short antenna problem shows up again, and a shrimp dies once every few days.  I am not sure what causes things to go bad, but usually over the course of a few days I will start to see more shrimp quietly standing on the HMF filter, and so I know something is wrong.  Since I am not "doing anything" besides the regular 1-2 week water changes, I just assume that something bad is building up.  Here's a list of things that I've tried that are supposed to be "can't hurt" but didn't prevent the problem either: Dose every other day with Shrimp Fit (very small dose, and the shrimp seem to like it) Sotching Oxydator Seachem Purigen to keep the nitrates lower Keeping the pH below 5.5 with peat Things that I don't do often, so could possibly "reset" the tank back to a good streak, are gravel vac and plant trim, so maybe time to try those again. One other problem I used to have was that sometimes a shrimp would suddenly stop eating with a full or partially full digestive tract that doesn't clear out, and then the shrimp will die within a few days.  I suspected it was one of the foods in my rotation - Shrimp Nature Infection, which contains a bunch of herbal plant things.  I've had this in my food rotation for a few years now and generally didn't seem to cause problems, but I removed it from the rotation anyway.  I don't have a lot of adult Golden Bees at this point so I can't really tell if it worked or not. Overall the tank is not too bad - during the good streaks occasionally a shrimp will get berried and hatch babies with a 33-50% survival rate.  So while there are fewer adults now, there are also a bunch of babies roaming around.  I guess this tank will stagger on, but I really do need to take the time to start up a new tank.  (or figure out the problem)
    • jayc
      If that is the offspring, then the parents are unlikely to be PRL. I tend to agree with you. There are very few PRLs in Australia. And any that claim to be needs to show proof. PRL genes have to start as PRL. CRS that breed true after x generations doesn't turn it into a PRL. Neither can a Taiwan bee shrimp turn into a PRL despite how ever many generations. I've never seen a PRL with that sort of red colour. I have on Red Wines and Red Shadows - Taiwan bee shrimps. So somewhere down the line one of your shrimp might have been mixed with Taiwan bees and is no longer PRL. It just tanks one shrimp to mess up the genes of a whole colony. 
    • sdlTBfanUK
      Sorry, missed this one somehow! The PRL look fantastic and the odd ones look part PRL and part Red wine/Red shadow in the colour. They are still very beautiful but ideally should be seperated to help keep the PRL clean if you can do that.  Nice clear photos!
×
×
  • Create New...